yokogawa tc10 l manual

Fr 8am to 5pm ET, The Yokogawa TC10-L Temperature Controller is recommended replacement. Safety, Protection, and Modification of the Product, - In order to protect the system controlled by this product and the, product itself, and to ensure safe operation, observe the safety, precautions described in the Engineering manual. of use, service life and misuse are not covered by this warranty. There is minimum vibrations and no impact; 4. equipment and devices that ensure personnel safety. OUTLINE DIMENSIONS (mm) 1.1 INSTRUMENT DIMENSIONS 48 PV Optional gasket 1.2 PANEL CUT-OUT 45 +0.6 mm 1.78 +0.023 -Use copper conductors only. Pages: 30 . If this instrument is used in a manner not specified in this manual. Can I output in the 100% direction (20 mA or more) upon burnout? TC10 TEMPERATURE CONTROLLER Engineering Manual Code: IM 05C01E81-02EN Third edition: Feb. 2018 Yokogawa Electric Corporation 2-9-32 Nakacho, Musashino-shi, Tokyo 180-8750 Japan www.yokogawa.com/ns 1. 18 months (a year and a half) after shipment from the factory. - Installation of protection and/or safety circuits with respect to a, lightning protector; protective equipment for the system controlled, by the product and the product itself; foolproof or failsafe design, of a process or line using the system controlled by the product or, the product itself; and/or the design and installation of other, protective and safety circuits are to be appropriately implemented, - This product is not designed or manufactured to be used in critical, applications that directly affect or threaten human lives. Note: For TC and RTD inputs the decimal figure must be 0 or 1 only. The following general safety precautions must be observed during. - This product is intended to be handled by skilled/trained person-, - This instrument is for Measurement Category No. The instrument behaviour and its performance are governed by the value of the stored parameters. and access the next parameter within the same group. This instrument is intended for permanent installation, for indoor use only, in an electrical panel which encloses the rear housing, exposed terminals and wiring on the back. 2.External components (like zener barriers, etc.) The UT52A/MDL supports 920 MHz band wireless communication. A ladder sequence function is included as standard. 4 2.4 SERIAL INTERFACE. 4. Wattmeter Instantaneous power is continuously computed, as multiplication of the Load Voltage, Load Current parameter. View and Download Yokogawa TC10-L instruction manual online. What is the input resolution specification the TC10? The UT75A temperature controllers employ an easy-to-read, 14-segment large color LCD display, along with navigation keys, thus greatly increasing the monitoring and operating capabilities. The ambient temperature is in accordance with the operative, 6. Do not run logic input wiring together with power cables; The instrument needs 150 ms to recognize a contact status variation; To avoid electrical shocks, connect power line at last. The TC10-L features universal input, 3 Dynamic Colors Led Display two alarm outputs, retransmission output, a timer to count the total time the setpoint is exceeded, and a register to retain the maximum temperature reached. These two keys allow to return to the previous. Can't find your region? Line resistance: Automatic compensation up to 20W/wire with maximum error 0.1% of the input span. {{ baseCtrl.fullNavList[baseCtrl.fullNavList[baseCtrl.currentMenuDepth].parent].name }}, {{ baseCtrl.fullNavList[baseCtrl.currentMenuDepth].name }}, Special Solutions of OpreX Transformation, Visual MESA Supply Chain Scheduling (VM-SCS), Visual MESA Production Accounting (VM-PA), Cloud Inventory Management Solutions (Web*VMI), Platform for Advanced Control and Estimation (Advanced Process Control), OpreX Laboratory Information Management System, Remote Plant Performance Operation and Remote Consulting (KBC Co-Pilot Program), Predictive Maintenance of Pump Cavitation, Advanced Analytical Instrument Management System (AMADAS), FluidCom Chemical Injection Flow Controller, Real-time Plant Data Sharing Service (Web*Technician), Digital Plant Operation Intelligence (DPI) Quality Stabilization System, OpreX Data Model Broker / Design Data Validation, OpreX Customer Service Management Software, OpreX IT/OT Security Operations Center (SOC), Plant Information Management System (Exaquantum), Alarm Reporting and Analytics (Exaquantum/ARA), Integrated Production Information (Exaquantum/mPower), Power Performance Calculations (Exaquantum/PPC), Safety Function Monitoring (Exaquantum/SFM), Operator Trending Module (Exaquantum/OTM), Remote Data Synchronization (Exaquantum/RDS), Synchronous OPC DA Manager (Exaquantum/SDM), Manufacturing Data Exchange (Exaquantum/MDX), Public announcement of Yokogawas products, Single-Cell Analysis Solution Single Cellome, Distributed Temperature Sensor - Fire Detection/Fire Prevention -, Industry and Interface Libraries (Applications and Interfaces), Advanced Control Bioreactor System BR1000, ALH for FlowCam: Automated Liquid Handling, Yokogawa announcement to Windows XP users regarding Systems products, A Business Value Decision ofImpact and Significance, Yokogawa Cloud IT/OT Connectors & Integrations, Support InformationNew Legislative Framework (NLF) Conforming Products, Temperature Control for Seal-heating Parts in Wrapping Machinery. Can I hide the SP display? Assign OP4 to the control output operation. If thePV does not exceed SP, after the conrming operation, output relay will be energized (closed) and the output (OUT) display lamp turns off . View and Download Yokogawa UT55A instruction manual online. Can I use the DI function to switch between auto/manual and between run stop/start? The TC10 supports easy configuration with codes for quick start-up. The shallow depth of the controller helps to save instrument panel space. Pt 1000 calibration: According to EN 60751/A2. Allows to increase the value of the selected parameter. 600W. 1, This instrument is intended for permanent installation, for, indoor use only, in an electrical panel which encloses the. 2. To protect the AL2 and AL3 thresholds against, undesired changes, they are available only at "Parameters, list" level (password: 20). Copyright 1994-2023 Yokogawa Electric Corporation. For supply connections use No. 6. Worked Time counter is continuously increased when, Overall dimensions (L x H x D): 48 x 48 x 73 mm, This instrument is intended for permanent installation, for indoor. use only, in an electrical panel which encloses the rear housing. 1. rear housing, exposed terminals and wiring on the back. NOTE: This parameter will be shown only when a TC or RTD input has been selected. The UT75A temperature controllers employ an easy-to-read, 14-segment large color LCD display, along with navigation keys, thus greatly increasing the monitoring and operating capabilities. There's no SG terminal for wiring RS485 communication on the TC1. the protection provided by this instrument may be impaired. The. On burnout, it will be 0 mA. If this instrument is used in a manner not specified in this manual. A ladder sequence function is included as standard. To protect the AL2 and AL3 thresholds against, undesired changes, they are available only at "Parameters, list" level (password: 20). There is no parameter for specifying the output direction. For SSR, mA and V outputs if the line length is longer than 30 m use a shielded wire. The ambient temperature is in accordance with the operative, 6. On the TC10, I want the difference lower limit alarm to be ON 5C below the setpoint value. Yokogawa Electric Corporation for this Product in the EEA. Available: When a linear input is selected by [1] SenS. The shallow depth of the controller helps to save instrument panel space. The instrument have one complete parameter set. It has been designed, with compliance to the European Directives. The following symbol is, This manual is an essential part of the product; keep it in a safe place for. Can I use the DI function to switch between auto/manual and between run stop/start? All information about the controller use can be found in the Engineering Manual: IM 05C01E81-12EN and the Communication Manual: IM 05C01E81-13EN and General Specification: GS 05C01E81-11EN. It has been de- signed with compliance to the European Directives. Available: When a linear input is selected by [1] SenS. Please, provide a T type 1A, 250 V fuse externally. Notes: 1. Safety, Protection, and Modification of the Product, - In order to protect the system controlled by this product and the, product itself, and to ensure safe operation, observe the safety, precautions described in the Engineering manual. It has been designed, with compliance to the European Directives. : input type, Control strategy, alarms, etc.). future reference. There is no parameter for specifying the output direction. The following, Calls attention to actions or conditions that could cause serious or, fatal injury to the user or damage to the instrument, and indicates, precautions that should be taken to prevent such occurrences. AL on the front of the TC10 is the alarm lamp. The EU Declaration of Conformity and the manual of the controller. Before connecting the output actuators, we recommend to congure the parameters to suit your application (e.g. [13] AL1 and [30] AL2 will be forced to : for an absolute maximum alarm, them will be forced to the maximum input span, for an absolute minimum alarm, them will be forced to the minimum input span, for all other alarm, them will be forced to zero, [14] HAL1 and [31] HAL2 will be forced equal to the 0.5% of the input span, [35] HYS will be forced equal to 0.05 % of the input span, the CAL group will be reset [51]A.L.P, [52] A.L.O, [53] A.H.P, [54] A.H.O. Can I turn off the "C" display with input other than temperature on TC10? Moreover, provide indication that the. Download this manual TEMPERATURE CONTROLLER Model: TC10 - Quick Guide . The UT35A and UT32A temperature controllers employ an easy-to-read, 14-segment large color LCD display, along with navigation keys, thus greatly increasing the monitoring and operating capabilities. I'm looking for a replacement for the UD310. IM 05C01E81-01EN, 2-9-32 Nakacho, Musashino-shi, Tokyo 180-8750 Japan, EU Declaration of conformity and Manual retrieval, TC10 is a panel mounting, Class II instrument. connected to the low-voltage installation. 0/4 to 20 mA input wiring for passive transmitter using the auxiliary pws. The conguration parameters are collected in various groups. user must refer to the Engineering manual for special instructions. YOKOGAWA TC10-L: Quick Manual| Brand: Want to have your manuals available on hand: always and everywhere? The TC10 is a compact temperature single loop controller with easy -to-read 3 dynamic colors led display. This is a list of recorder and controller products that support the New Legislative Framework (NLF.). : 500W. 18 months (a year and a half) after shipment from the factory. To change these parameters you need to enter the Conguration mode. 3. values and the controller output instantaneous value. YOKOGAWA TC10-L Quick Manual; YOKOGAWA TC10-L Quick Manual. Search the full list . - Install the power cable keeping a distance of more than 1 cm from, - The power cable is required to meet the IEC standards concerned or the. It also includes a ladder sequence function. condensation); 5. IP65 rated as "dust tight" and protected against water projected from a nozzle when the optional panel gasket is mounted (for indoor locations) according to EN 60070-1. TC10-Ls compact design allows for a broad range of applications/uses while maintaining a high level of accuracy.

Nba 2k22 Expansion Cities List, What Does R 4 Mean In Linear Algebra, Articles Y